ILT-U-525Abrasion Resistance of Organic Coatings by the Taber Abraser

Description: Method: ASTM D4060

ILT-U-2088Air Filter determinations

Description: Marking and labelling Method: SASO 932, GSO 1712

ILT-U-1016Alcohol absolute determination

Description: Ethanol content of 20 ° C; higher alcohols; METHANOL; aldehydes; ESTERS; ACIDITY; CONDUCTIVITY Method:

, ILT-U-1295Automotive battery determination

Nominal Capacity test (C20)

ILT-U-2270Ballistic determinations

Resistance level I-A, I-B, III-A, III-B, III-C, IV-A, IV-B, IV-C, V-A, V-C

ILT-U-293Benzene determination charcoal tubes

Description: NIOSH 1501 Method: NIOSH 1501

ILT-U-1506BTEX determination in activated carbon


ILT-U-1565calorific value determination

Description: Determination of the gross heat of combustion Method: ISO 1716

ILT-U-1693Carbon determinations

Description: Iodine Number-Carbon Black; Oil Absorption Number; Crushed Oil Absorption Number; Tint Strength; Sieve Analysis-Carbon Black – 35 Mesh; Sieve Analysis-Carbon Black – 325 Mesh; Pellet Hardness; and N2SA/STSA Method: ASTM D6556, ASTM D1514, ASTM D3265, ASTM D2414, ASTM D1510, ASTM D5230, ASTM D3493

ILT-U-2079Castors and wheels determination

Description: Castors and wheels Type U+ Type H Method: EN 15259

ILT-U-2077Castors and wheels determination. 1B

Description: Castor test Method: EN 12527, EN 12528

ILT-U-1999Coal determinations

Description: Te and Sn elements Method:

ILT-U-1134Cobalt and Arsenic determination in human urine

Cobalt and Arsenic

ILT-U-1714Color difference and reflectance

Description: Color and reflectance (250nm to 2500nm) Method: ASTM E903

ILT-U-1898Colour Reference determination. OT

Description: Y, x, and y values Method: ASTM D6045, ASTM D1500

ILT-U-1653Connectors determinations

Description: Dimensional requirements; positive pressure liquid leakage; subatmospheric-pressure air leakage; stress cracking; resistance to separation from axial load; resistance to separation from unscrewing; and resistance to overriding Method: ISO 80369-7

ILT-U-1315Consistency of Paints Measuring Krebs Unit (KU) Viscosity

Description: Using a Stormer-Type Viscometer Method: ASTM D562

, ILT-U-2371Contents of elements in hay powder

Ca, K, Mg, P, S, Zn, I, N and Kjeldahl-N

, ILT-U-2318Covered kitchen recessed gas determinations

Gas circuit tightness test, Obtaining test of the nominal calorific consumption (work table), Test to obtain the minimum calorific consumption (work table), Performance test of gas appliance burners for cooking food (Work table), Oven Maintenance Consumption Test (Oven or grill)

ILT-U-518Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet)

Description: Method: ASTM D5894

ILT-U-1272Cytotoxicity test in Suture thread

Description: Method: ISO 10993-5

ILT-U-529Determination of brucellosis in bovine serum lyophilized

Description: Lyophilized Method: Lyophilized

ILT-U-1366Determination of Copper impurities.

Description: Determinations: Sb, Pb, Bi, Cu, Fe, As, In, Co, Zn, Ni, Al, S, Cd, Ag and others Method:

ILT-U-1401Determination of density in paints

Description: Density (Picnometric Method) Method: ISO 2811

ILT-U-1607Determination of dry thickness. OT

Description: Painted sheet sample Method: ASTM D5796

ILT-U-1929Determination of Ethylbenzene

Description: GC-mass, adsorbed on activated carbon tubes in air samples. Method:

ILT-U-1140Determination of resistance to humidity. OT

Description: Method: ISO 6270-2

ILT-U-1307Determination of silica in phosphoric rock

Description: Silicon Oxide (%SiO) – Gravimetric Method Method:

ILT-U-1311Determination of the mechanical properties off glass fibre meshes

Description: Method: EN 13496

ILT-U-1588Determinations for environmental conditioning. 1A

Description: Determination of the steady state thermal resistance and related properties-Hot plate guard apparatus Method: NCh 850, ISO 8302

ILT-U-1602Determinations for environmental conditioning. 1B

Description: Determination of the thermal resistance in steady state and related properties-Calibrated thermal camera and guard Method: ISO 8990, NCh 851

ILT-U-1248Determinations in biomedical materials

Description: Determination of residual ethylene oxide; Determination of ethylene chlorohydrin and ethylene glycol, Method: ISO 10993-7

ILT-U-1489Determinations in expansible polyurethane

Description: Tear resistance in flexible polyurethane foam; and Tensile strength in flexible polyurethane foam. Method: NBR 8515, NBR 8516

ILT-U-1521Determinations in lithium brine

Description: Density at 25 °C; Calcium; Chloride; Copper; Total dissolved solids; Strontium; Sodium; Chrome; Sulfates; Iron; Aluminum; Lithium; Arsenic; Magnesium; Barium; Manganese; Lead; Zinc; Boron; and Potassium Method:

ILT-U-331Determinations in phosphate rock. OT

Description: Phosphorus Pentoxide (%P2O5); Silicon Oxide (%SiO); Fe2O3, Al2O3, MgO, K2O, Na2O, Cd, Sr, CaO; and Total chloride (ppm Cl) Method:

ILT-U-849Determinations in Refractory material. 1A

Description: Pyrometric cone equivalent; Continuous linear variation until 1300; Cold crushing strength dense shaped; Determination of refractoriness under load with rising temperature; and Resistance to thermal shock Method: EN 993-10, EN 993-11, EN 993-12, EN 993-5, ASTM C113, ASTM C1171, ASTM C24, EN 993-8

ILT-U-1904Determinations in Refractory Material. 1B

Description: Determination of cold crushing strength dense shaped refractory products. Method: EN 993-5

ILT-U-1485Determinations on health products

Description: Meter evaluation; Evaluation of mixers; Evaluation of showers; Evaluation of toilets; and Evaluation of intake and discharge valves Method: NOM-012-SCFI-1994, NOM-009-CONAGUA-2001, NOM-008-CONAGUA-1998, NOM-010-CONAGUA-2000, NMX-C-415-ONNCCE-2015

ILT-U-832Dimensional stability determination in thermal insulating products for building applications.

Description: Method: EN 1604

ILT-U-2048Disc Brake Pad determinations. 1A

Description: Compressibility – Cold – Hot and Heat Expansion; Bond Shear Strength; Internal Shear Strength after prolonged exposure to water, saline, lube oil, Brake Fluid; and Coeff. of Friction & Wear (KRAUSS TEST) Method: ISO 6310, ISO 6312, ISO 6313, ISO 6311, ISO 6314, SAE-J840, SAE-J2468, UNECE-R 90

ILT-U-2059Disc brake pad determinations. 1B

Description: VISUAL TEST & INSPECTION: Identification of defects by Physical examination and other simple tests like sound test, tap test, optical test. Method: IEC 22574

ILT-U-1380DNA Test – Mitochondrial DNA

Description: Analysis of Mitochondrial DNA, and includes a sequencing of hypervariable regions of mitochondrial DNA (maternal inheritance). The analysis includes the sequencing of the hypervariable regions HVI, HVII and HVIII of mitochondrial DNA. Method:

ILT-U-1378DNA Test – XSTR Markers

Description: analysis of genetic markers of the Short Tandem Repeat (STR) type located on the X chromosome (maternal inheritance in males, and bi-parent in females. The analysis includes the following 10 X-STRs: DXS8378, DXS9898, DXS7133, GATA31E08, GATA172D05, DXS7423, DXS6809, DXS7132, DXS9902, DXS6789. Method:

ILT-U-1379DNA Test – YSTR Markers

Description: analysis of genetic markers of the Short Tandem Repeat (STR) type located on the Y chromosome (paternal inheritance). The analysis includes the following 23 Y-STRs: DYS389II, DYS389I, DYS390, DYS193, DYS393, DYS392, DYS439, DYS437, DYS391, DYS385, DYS438, GATA H4, DYS456, DYS458, DYS635, DYS448, DY576, DY481, DY549, DY533, DY570 and DY643 (PowerPlex® Y23 System). Method:

ILT-U-1995Domestic cooking appliances burning gas determinations. OT

Description: Combustion and Consumption Method: EN 30-1-1

ILT-U-1400Drying, Curing, or Film Formation of Organic Coatings

Description: Curing, or Film Formation of Organic Coatings Method: ASTM D1640

ILT-U-857Durability of shock absorbers

Description: NBR 13308 item 4 Method: NBR 13308

ILT-U-1734Engine and Exhaust Engine determinations

Description: Measurement of CO & HC; and Measurement of Engine Operation Efficiency Method: SASO 1284, GSO 971, SASO 267, GSO 40

ILT-U-1900Ethanol determination. OT

Description: 40 % ABV (Alcohol by Volume). Method:

ILT-k-05Ethanol determinations. Water impurities, sulphur, chlorides, sulfates, and density.

Description: EN 15489; EN 15486; EN 15492 and ASTM D4052 Method: EN 15486, EN 15489, EN 15492, ASTM D4052

ILT-U-959Fertilizers determinations, 1A

Description: 1-naphthylacetamide; 2,4, -D; 4-CAP; 6-benzyladenine; 1 naphthylacetic acid; 3- indolacetico; 3indolbutirico acid; gibberellic acid; MCPA sum; MCPA; MCPB; forchlorfenuron; and vitamin B1 Method:

ILT-U-1040Fertilizers determinations. 1B

Description: Bifenthrin 10 E.C. – Active content; and Methoxyfenoxide 240 g/lit SC – For Active content and suspensibility test. Method:

ILT-U-879Fertilizers determinations. 1C

Description: P2O5, K2O, Cd, Cr, Pb, As, and Hg Method:

ILT-U-529Film Hardness by Pencil Test

Description: Method: ASTM D3363

ILT-U-1047Film thickness measurement in paints and varnishes

Description: Method 6a. Method:

, ILT-U-2313Fire extinguishers determination

force test

ILT-U-1384Fire extinguishing powder determination

Description: Humidity Method:

ILT-U-1899Flash Point determination. OT

Description: Using Procedure A and corrected for the barometric pressure at time of determination. (Nominal value: 175.0 °C) Method: ASTM D93

ILT-U-146Flatwise Tensile of Sandwich Core Materials. OT

Description: Method: ASTM C297

ILT-U-2118Flexible and Rigid Insulated Temporary By-Pass Jumper. OT

Description: Flexible and Rigid Insulated Temporary By-Pass Jumper determinations Method: ASTM F2321

, ILT-U-2378Fluorine determination in clay


ILT-U-2060Full-flow lubricating oil filters for internal combustion engines

Description: Differential pressure/flow characteristics Method: ISO 4548-1

ILT-U-2065Full-flow lubricating oil filters for internal combustion engines. 1A

Description: Filtration efficiency using particle counting and contaminant retention capacity Method: ISO 4548-12

ILT-U-2062Full-flow lubricating oil filters for internal combustion engines. 1B

Description: Hydraulic pulse durability test, and Cold start simulation test Method: ISO 4548-5

ILT-U-2064Full-flow lubricating oil filters for internal combustion engines. 1C

Description: Inlet anti-drain valve test Method: ISO 4548-9

ILT-U-2061Full-flow lubricating oil filters for internal combustion engines. 1D

Description: Element by-pass valve characteristics Method: ISO 4548-2

, ILT-U-2317Gas step Heater determinations

Gas circuit tightness test, Nominal calorific consumption test, Minimum calorific consumption test, Rational use of energy test. Performance, Performance characteristics test. Useful, nominal and minimum powers, Performance characteristics test. Automatic gas operated valve by high and low pressure water

ILT-U-1652Gas-fired central heating boilers determinations

Description: Performance 100% and performance 30% Method: EN 297, EN 625

ILT-U-2372Glass determinations

Chemical composition

ILT-U-2083Glass in building

Description: Glass fragmentation Method: EN 12150

ILT-U-1252Glow discharge optical emission spectroscopy

Description: Method: ISO 14707

ILT-U-2028HF (Halogen) in semiconductor device determination. OT

Description: HF (Halogen) Method: EN 14582

ILT-U-1383Implants for surgery

Description: Surfactants Method:

ILT-U-2071Inner tube determinations

Description: Tensile & Elongationñ and Ageing Test Method: JIS D4231

ILT-U-1987Ladder determinations. OT

Description: Method: EN 131-2

ILT-U-2130Lead acid automotive battery

Description: Automotive Electrical System Battery Method: GSO 35, GSO 34, SASO 1920, SASO 1919

ILT-U-974Lead glass determinations

Chemical composition, Density, Refractive index value

ILT-U-1177Lead in paint determination. 1A OT

Description: Method AOAC 974.024 / ICP. Method: 16 CFR Part 1303

ILT-U-1687Lead in Paint determination. 1B

Description: Galvanized Steel and Pre-painted Galvanized Steel, samples Method: ASTM E1613

ILT-U-1174Linear Alkyl Benzene Sulphonic (LABSA) determinations

Description: Linear Alkyl Benzene Sulphonic acid (LABSA): Active matter and Free Oil (Non Detergent Organic matter) Method: ASTM D3049, IS 8401

ILT-U-1020Lubricating oil determinations. OT

Description: Flash Point -Miniflash; Total Neutralized Acid; Kinematic viscosity; Total Neutralised Base; Infra-red; and Particle Counting Method: ASTM D7596, ASTM D445, ASTM D664, ASTM D6450, ASTM D2896, ASTM E2412

ILT-U-470Mandrel Bend Test of Attached Organic Coatings

Description: Method: ASTM D522

ILT-U-863Metal determinations in fertilizers

Description: Zinc , Potassium, Calcium, Copper, Manganese, Phosphorus, Iron, Nickel, Cobalt, and Boron Method:

ILT-U-1695Metals and metalloids determination

Description: Metals and metalloids Method: GMC 15

ILT-U-944Metals determinations in air sample

Description: Lead and Metals Method:

, ILT-U-2379Migration of elements in Pigments

Migration of the elements (arsenic, cadmium, zinc, mercury, lead, selenium, chromium, antimony and barium) determination, with 0.1M hydrochloric acid solution in powdered pigment sample

ILT-U-086Moisture and Ash in tobacco products

Moisture and ash

ILT-U-927Moisture content in charcoal briquettes. OT

Description: Method: EN 1860-2

ILT-U-1831NOx reduction agent AUS 32 determination

Description: Urea Content; Density@ 20 deg.; Refractive Index; Alkalinity; Biuret content; Insoluble Matter content; Identity (FTIR); Aldehyde Content; Phosphate content; Elemental Analysis : (Elemental Contamination); Calcium; Iron; Copper; Zinc; Chromium; Nickel; Aluminium; Magnesium; Sodium; and Pottasium Method: ISO 22241-2

ILT-U-1573Object color evaluation

Description: Spectrometric data for object-color evaluation and calculation of color tolerances and color differences from instrumentally measured color coordinates Method: ASTM E1164, ASTM D2244

ILT-U-1963Oil adsorption determination

Description: Oil Adsorption Method: ASTM D281

ILT-U-2070Oil Filter determinations

Description: Full-flow lubricating oil filters for internal combustion engines Part 6: Static burst pressure test Method: ISO 4548-6

ILT-U-522Oxygen gas transmission rate determination

Description: Method: ASTM F1227

ILT-U-1648Paint determinations. 1A

Description: VOC; heavy metals (Pb, Cr, Cd, Sb, Hg & As); chemical resistance; and aromatic hydrocarbon Method: ISO 11890-1, WL-IP-028, ASTM D3257, ASTM D1308

ILT-U-1516Paint determinations. 1B

Description: Density; pH; and Non-volatile-matter content Method: ISO 2811, ISO 787-9, ISO 3251

ILT-U-1688Paint dry film thickness determinations

Description: Galvanized Steel and Pre-painted Galvanized Steel, samples Method: ASTM D5796

ILT-U-187Paints and varnishes

Description: Cross-cut test, Determination of film thickness Method: ISO 2409

ILT-U-201Paints and varnishes — Determination of resistance to humidity

Description: ISO 6270-1 Method: ISO 6270-1

ILT-U-887Paints and Varnishes determination

Scratch resistance

ILT-U-1098Paints and Varnishes determination

Bend Test (Cylindrical Mandrel)

ILT-U-2024Paints and varnishes determination. 1B

Description: Film thickness Method: ISO 2178

ILT-U-2025Paints and varnishes determinations. 1A

Description: Coating Thickness Amplitude Sensitive Eddy Current (Eddy Current) Method Method: ISO 2360

, ILT-U-2343Pallet plastic determinations

Stacking, Forklifting, Block Compression, Racking Tests

ILT-U-1377Parental DNA Test

Description: analysis of genetic markers of the Short Tandem Repeat type (STR) located on autosomal chromosomes (biparental inheritance). The analysis includes the following 32 STRs: D3S1358, THL1, D21S11, D18S51, vWA, D8S1179, TPOX, FGA, D5S818, D13S317, D7S820, D16S820, D16S539, CSF1PO, Amylogenin, PENTA_E, PENTA_D, D2S1338, D19S433, D1S1656, D12S391, D2S441, D10S1248 and D22S1045 (Powerplex Fusion System) and D7S1517, D3S1744, D2S1360, D6S474, D4S2366, D8S1132, D5S2500, D21S2055, D10S2325 and SE33 (HDPlex). Method:

ILT-U-2332Pedestal wash basins determinations

Diameter of the tap hole, Horizontal distance between the centre line of the tap hole to the edge of the bowl, Width of the flat plane of the tap platform from the centre of the tap hole to the back edge of the flat plane, Distance form the centre line of the tap hole to the backwall

ILT-U-569Physical determinations in tobacco products

Description: Method: ISO 6565, ISO 2971

ILT-U-929Porosity analysis of Carbon black

Description: 40 – Point analysis – (Nitrogen Gas) Method: ASTM D4641

ILT-U-930Powder flowability study

Description: Freeman technologies FT4 Powder rheometer Method:

ILT-U-1917Qualitative analysis of solvents mixture

Description: GC/MS Scan Industrial. EPA 8015 Method D Method: EPA 8015

ILT-U-2373Rare element value in Duck-Weed (aquatic plant)

Ce, Dy, Er, Eu, Gd, Ho, La, Lu, Nd, Pr, Sc, Sm, Tb, Tm, Y, Yb, Th, U

, ILT-U-2374Rare element value in estuarine sediments

Ce, Dy, Er, Eu, Gd, Ho, La, Lu, Nd, Pr, Sc, Sm, Tb, Tm, Y, Yb, Th, U

, ILT-U-2377Rare element value in mussel tissue (Mytilus edulis)

Ce, Dy, Er, Eu, Gd, Ho, La, Lu, Nd, Pr, Sc, Sm, Tb, Tm, Y, Yb, Th, U

ILT-U-834Reaction to fire determination in construction products and building elements. OT

Description: Classification to the Reaction to Fire, performing the following test: Determination of gross combustion heat (Calorific value), and Non-combustibility test Method: EN 13501-1, ISO 1716, ISO 1182

ILT-U-522Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)

Description: Method: ASTM D2794

ILT-U-858Rock phosphate determinations

Description: Phosphorus pentoxide (%P2O5); Silicon oxide (%SiO); and Fe2O3, Al2O3, MgO, K2O, Na2O, Cd, Sr, CaO Method:

ILT-U-1732Rotational Viscosity determination

Description: corrosion inhibitor Method: ISO 3219

ILT-U-2299Sanitary tapware determinations

Standard :

ILT-U-1065Sieve residue analysis in construction plaster. OT

Description: Sieve residue analysis (clause 4.1.3) Method: EN 13279-2

ILT-U-1849Specific Migration of PAH and formaldehyde and acetaldehyde. OT

Description: Specific Migration of PAH (Deionized Water, or 3% Acetic Acid, or Olive Oil) and specific migration of formaldehyde and acetaldehyde (Deionized Water, and 3% Acetic Acid) Method: EN 13130-1

ILT-U-535Specular Gloss

Description: Method: ASTM D523

ILT-U-516Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

Description: Method: ASTM D1894

ILT-U-1621Swabs & Surfaces determinations

Description: Aerobic mesophilic (total count); Salmonella (Absence/presence); and Escherichia Coli O157 H7 (Absence/presence) Method:

ILT-U-1689T Bend Adhesion of paint determinations

Description: Galvanized Steel and Pre-painted Galvanized Steel, samples Method: ASTM D4145

ILT-U-833Tensile strength parallel to faces in thermal insulating products for building applications.

Description: Method: EN 1608

ILT-U-237Test Method for 90 Degree Peel Resistance of Adhesives. OT

Description: ASTM D6862 Method: ASTM D6862

ILT-U-1332Thermal insulating products determination

Description: Determination of bending behavior; Determination of deformation under specified compressive load and temperature conditions; and Determination of compression behavior Method: EN 826, EN 1605, EN 12089

ILT-U-831Thermal resistance and thermal conductivity in thermal performance of building materials and products.

Description: Method: EN 12667

ILT-U-635Tile adhesives determination

Description: Initial adhesion with different adhesive products provided for placement: C1, C2, D1, D2, R or mortars, Method: EN 12004

ILT-U-1087Total and external surface area by nitrogen adsorption

Description: Carbon black Method: ASTM D6556

ILT-U-1132Total N, P2O5, K2O determinations in liquid fertilizer (Vinasse)

Description: Vinasse sample Method:

ILT-U-2041Transformer oil determination. 1A

Description: Dissipation factor (delta tangent at 90º) Method: ASTM D924

ILT-U-2040Transformer oil determination. 1B

Description: Neutralization number analysis Method: ASTM D664

ILT-U-2039Transformer oil determination. 1C

Description: Particle count and resulting ISO code Method: ISO 4406

ILT-U-2038Transformer oil determination. 1D

Description: Corrosive sulfur (Method B) Method: ASTM D1275

ILT-U-2037Transformer oil determination. 1E

Description: DBPC Inhibitor content Method: ASTM D4768

ILT-U-2036Transformer oil determination. 1F

Description: Interfacial tension measurement Method: ASTM D971

ILT-U-2032Transformer oil determination. 1G

Description: Dissolved Gas Method: ASTM D3612

ILT-U-2033Transformer oil determination. 1H

Description: Products of the degradation of cellulosic materials Method: ASTM D5837

ILT-U-2034Transformer oil determination. 1J

Description: PCBs content Method: ASTM D4059

ILT-U-2035Transformer oil determination. 1K

Description: Moisture content Method: ASTM D1533

ILT-U-1201Triterpene glycosides (HPLC) determination

Triterpene glycosides

ILT-U-751True density determination

Description: Accupyc II – True density (non-metal powder) Method: ASTM B923

ILT-U-1441Urethane foam determination. 1A

Description: Method E – Tensile Strength / Elongation Method F – Tear Strength Method G – Air Flow Method H – Ball Rebound Test Method: ASTM D3574

ILT-U-1442Urethane foam determination. 1B

Description: Method A – Density Method B1 – Hardness Method D – Compression Set at 50% Deflection Method: ASTM D3574

ILT-U-1641Urine determinations

Description: 2,5 Hexanodione; muconic acid; orto-cresol; and acid methyl hippuric Method:

ILT-U-835Water absorption in thermal insulating products for building applications

Description: Method: EN 1609

ILT-U-2297WC determinations

Standard :

ILT-U-2296WC determinations

Standard :

, ILT-U-2047Wheels determination. 1A

Description: Impact test (single Hit) Method: ISO 7141

, ILT-U-2046Wheels determination. 1B

Description: Radial fatigue test (600.000 cycles) and Cornering Fatigue Test (50.000 cycles) Method: ISO 3006

, ILT-U-2375White cabbage elements value

Cd, Cu, Fe, Mn, Mo, Ni, Sr, Zn, Hg, Sb, Tl

, ILT-U-2376White clover elements value

As, Co, Mo, Se

Category of Schemes
ILT – Interlaboratory Test
Scroll to Top
  • No products in the cart.